Recirculating Torlon ball bearings allow genoa lead cars to adjust easily under full sheet loads.

Sheaves feature ball/roller bearings with sideload balls for easy trimming and fore/aft adjustment under load. Wide sheaves accomodate two sheets during sail changes. Sheave carriers pivot to accomodate changing lead angles.

Though Captive Ball track is specified here, none of these cars have Captive Balls, and come with a ball loader.

Slider cars run on ball bearing track. Roller/ball bearing sheaves pivot 60° for easy trimming.

The H323 has inner race slider rods to help lower friction. Slider rods can be replaced with ball bearings to make the cars adjustable under load. The car can be towed or used as a pinstop car.

Cars remove easily from the track to clean up deck.

Small Boat track comes in low or high-beam configurations. Use low-beam track when it's supported at each fastener hole. Use high-beam track when it must span a cockpit or other unsupported area. Choose between variable hole spacing and drilled for high-beam track.

Fasteners are 1 15/16" (50mm) from the end of the track on the metric track and 2" (51mm) on the Retrofit track.

Track can be bent to various custom curves. See below for more information.

**Fastens directly to the deck

	Oversized Shipping:
Due to the overall dimensions of Track over 60", our carriers classify them as "oversized". Please click here for more information.

Spring loaded pinstop cars offer two lead solutions for small keel boats from 22 ft to 27 ft (6 to 8 m).

The H2750 is for racers like the J/80 or Melges 24. Attach lightweight 57mm or 75mm Carbo blocks. Combine with H370 Stand-Up Boot for use with the 57mm Ti-Lite.

The H393_ Genoa Lead uses an axle bearing sheave. The sheave carrier pivots to accept unfair leads. Removable stop limits inboard pivoting so lead can mount near a cabin side.

Use the Small Boat track with Small Boat Pinstop Jib Leads. The track is also compatible with all non-pinstop Small Boat Captive Ball (CB) traveler cars.

	Oversized Shipping:
Due to the overall dimensions of Track over 60", our carriers classify them as "oversized". Please click here for more information.

Endstops and Trimcaps: Use H173 and H174 endstops for small dinghies and low-load situations. The H446 line-shedding endstop is low-profile and snag-free. The H263 and H264 heavy duty endstops absorb the shock loads of inintentional jibes and are used on larger dinghies and small keelboats. Use H2722 and H2723 trim caps to finish track ends when using control block assemblies. Sold in pairs. Fasteners not included.

Splice Links: Use the H2724 to join track and keep it aligned during installation.

Stand-up Toggles: The H2747 Small Stand-Up Toggle accepts 40mm double and triple Carbo AirBlocks and 57mm single and fiddle Carbo Airblocks. The H2748 Large Stand-Up Toggle accepts 57 mm double and triple Carbo AirBlocks.

Coupler: The H175 Coupler joins two cars for higher working loads. It is 3 11/16" (94mm) by 2 3/16" (56mm), weighs 4 1/2 oz (128g) and has a SWL of 1,500 lbs (680kg) and BS of 2,500 lbs (1134kg).

Wire High-Load Vang Block: The H384 couples with with a Small Boat car (especially the H382 Radial Traveler Car) to configure a radial vang. Sheave: 2" (51mm). Length: 2 3/4" (70mm). Weight: 3.3 oz (93g). Max Line Diameter: 1/4" (6mm). Max Wire Diameter: 5/16" (5mm). Car not included. SWL: 1,500 lbs (680kg). BS: 2,500 lbs (1134kg). Car sold separately.

Traveler Kit, 3 to 1: The H2739 includes 1 x H2735, 1 x H2743, and 2 x H348. Purchase track, trim caps, and control lines separately.

Control Tangs: The H2749 Control Tangs can be mounted on a Small Boat Car, as seen on the H2753 Car, allowing you to attach control blocks.

Track is often bent to follow the cabin house curve or boom radius. Sometimes track is bent vertically, ends up, to relieve tension on the sail's leech as the traveler car moves off the boat's centerline.

To perform smoothly and carry the correct load, the traveler car's length must suit track radius. Check the description of the traveler cars for their minimum radius requirements. Remember that you can couple two cars for higher loads on tighter radii.

Minor bends can often be made when the track is installed. If the track requires more bend, we can provide track with horizontal, vertical or compound curves to your specifications for a modest charge. If the bend is continuous, add 2 to 4 inches (50 to 100 cm) to each end because track cannot be bent to its ends. Standard Harken Mini-Maxi and Maxi traveler cars cannot ride on vertical bends with a radius under 50' (15.25m).

Please call to order curved track. We cannot accept curved track orders on our website. Please have ready the following information when you call:

• Boat Model:
• Track Part Number:
• Bend Part Number: (We'll help you with this)
• Chord Length:
• Chord Depth, Horizontal or Radius, Horizontal:
• Chord Depth, Vertical or Radius, Vertical:

And which curve you want (one of the following):

• Vertical Bend, Ends Down
• Vertical Bend, Ends Up
• Horizontal Bend, End Forward or Aft
• Compound Bend, Horizontal and Vertical, Ends Down
• Compound Bend, Horizontal and Vertical, Ends Up